Copper Talk » Open Forum » Archived Messages » 2003 » 01/01/2003 to 01/31/2003 » Silver eagle...problems!!! « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Donnie
Posted on Wednesday, December 18, 2002 - 5:27 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

The positive wire on the board came off an can not remember/figure out where it goes... can someone help me find the right spot?

DONNIE,

On the bottom of the board you will see:

A SMALL GREEN CAPACITOR,

Behind it you will See: A Resistor Br/BL/GR/GL

At the end of the resistor you will see a small hole right next to it, red wire goes in there.

This trace will run from the resistor all the way down board and around to another small Green Capacitor.

Red wire connects right straight down from green wire.

Hope this helps.

Lon
Tech808

Top of pagePrevious messageNext messageBottom of page Link to this message

Donnie
Posted on Thursday, December 19, 2002 - 12:53 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

thanxs 808----but i still can not find it. I don't see a green capacitor.... the resistor you mentiond br/bl/gr/gl... what is GL? an the only green wire i have is the one the runs from the end of the board to the head of the mic.. if you have anymore info i would be very gratfull. donnie
Top of pagePrevious messageNext messageBottom of page Link to this message

Buck
Posted on Thursday, December 19, 2002 - 6:01 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Donnie....the br/bl/gr/gl are the bands on the resistor....gl stands for gold
Buck
Top of pagePrevious messageNext messageBottom of page Link to this message

Tech808
Posted on Thursday, December 19, 2002 - 6:07 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Donnie,

OK, when you are looking at the bottom of the board, You should see a YELLOW wire then a green Wire and straight down from the green wire, 1/2 inch you will see a hole that should have a wire in it, this is where the RED wire goes.

The resistor is BROWN/BLACK/GREEN/GOLD

The little capacitor can also be BLUE

Either way you will have the hole for the green wire going to mic head then the hole with one end of resistor in it.

Then the hole that is missing the red wire.

ALL THREE HOLES ARE IN A STRAIGHT LINE.

If the First wire is not green it should still go to the head then count down 2 more holes (towards Volume control) and that is where the red wire goes.

Hope this helps!

Lon
Tech808
Top of pagePrevious messageNext messageBottom of page Link to this message

bruce
Posted on Thursday, December 19, 2002 - 10:32 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Hey lon did they teach the color code like this BAD BOYS ....... HE HE HE
Top of pagePrevious messageNext messageBottom of page Link to this message

Tech808
Posted on Saturday, December 21, 2002 - 5:00 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Donnie,

Did you get if figured out & fixed?

Lon
Tech808
Top of pagePrevious messageNext messageBottom of page Link to this message

Donnie
Posted on Saturday, December 21, 2002 - 7:34 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

yes 808 i did figure it out.. but now i am haveing problems wire it up to my 142gtl.. i have posted another message.. it is under silver eagle something i forget now.. it was posted on dec 21.. if u would read it an get back to me u can contact me eaiser at my e-mail address cause i do not check this every day... moparpower111@cs.com... if you could help me it would very apprciated
Top of pagePrevious messageNext messageBottom of page Link to this message

Funtimebob
Posted on Thursday, January 09, 2003 - 12:22 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

bruce- but violet gives :)
Top of pagePrevious messageNext messageBottom of page Link to this message

bruce
Posted on Thursday, January 09, 2003 - 8:32 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

YEP that the one HE HE HE !!!!!