| Author |
Message |
    
Spydrman
Junior Member
Username: Spydrman
Post Number: 40
Registered: 12-2001
| | Posted on Tuesday, February 24, 2004 - 4:00 pm: | 
|
I'm wondering if the six pin mic converter that copper sells will work for the Astatic 636 4 pin to the magnum omega force 6 pin?
Thanks,
spydrman |
Tech808
Moderator
Username: Tech808
Post Number: 1622
Registered: 8-2002
| | Posted on Tuesday, February 24, 2004 - 5:51 pm: |
|
NO,
Not unless your re-wire the C4PRI6 adapter.
The wiring for the Omega Force S-45 and the Ranger's are Different so it would be Much easier to just get a Standard 6 Pin Female Mic Plug and wire it for the Omega Force S-45.
OMEGA FORCE S-45 Wiring is:
PIN #1 ~ MICROPHONE AUDIO
PIN #2 ~ RECEIVE
PIN #3 ~ TRANSMIT
PIN #4 ~ UP/DOWN CHANNEL
PIN #5 ~ GROUND
PIN #6 ~ 13.8 Volts
(MAKE SURE NOTHING CAN COME IN CONTACT WITH THIS PIN)
Hope this helps.
Lon
Tech808
|
Highlander
Intermediate Member
Username: Highlander
Post Number: 422
Registered: 12-2001
| | Posted on Tuesday, February 24, 2004 - 7:51 pm: |
|
I thought that there were two 6 pin adapters, one for the Ranger 6 pin, and one for the Magnum 6 pin. I have one that converts from Galaxy 4 pin to my 6 pin Roadpro RPSY485, which, if I'm not mistaken, is the same wiring as posted above.
NOTE!
Sorry but no there are 5 adapter's and the C4PRI6 is the only 6 pin adapter
Lon
Tech808 |
Highlander
Intermediate Member
Username: Highlander
Post Number: 424
Registered: 12-2001
| | Posted on Tuesday, February 24, 2004 - 8:38 pm: |
|
I could post a link to it, it is model #C4PDF6, Cobra 4 pin to Delta Force 6 pin, but the site that has it is a competitor of Copper's. I have one of them, it works with "NO PROBLEMS".
|
Tech808
Moderator
Username: Tech808
Post Number: 1625
Registered: 8-2002
| | Posted on Tuesday, February 24, 2004 - 9:22 pm: |
|
Highlander,
I apologize as I did not know about the new Adapters for the Magnum.
I found it and checked it out and Yes it should work for you with no problems. I will ask the Forummaster to order these so he will have them on hand for the Copper Customer's.
Thank You, for bringing this new product to my attention.
Lon
Tech808 |
Tech808
Moderator
Username: Tech808
Post Number: 1626
Registered: 8-2002
| | Posted on Tuesday, February 24, 2004 - 9:25 pm: |
|
See, I told everyone you will never hear me say I know everything about anything.
There is so much new stuff coming out it is hard to keep up.
And I am always learning 
Lon
Tech808 |
Tech808
Moderator
Username: Tech808
Post Number: 1627
Registered: 8-2002
| | Posted on Tuesday, February 24, 2004 - 9:35 pm: |
|
ADDITION,
The  MAGNUM S-3 Has solved that problem as it Comes with a 4 Pin Mic wired the same as the Cobra / Uniden 4 pin radio's. 
Lon
Tech808 |
Jon666
Intermediate Member
Username: Jon666
Post Number: 104
Registered: 11-2003
| | Posted on Tuesday, February 24, 2004 - 9:36 pm: |
|
i have a coppers 4-6pin adapter.
it works good with my deltaforce.
whats up with that.
i didnt rewire it either? |
Yankee
Junior Member
Username: Yankee
Post Number: 24
Registered: 7-2003
| | Posted on Tuesday, February 24, 2004 - 9:53 pm: |
|
The adapters I need they don't list in any catalog. I want to keep all of my microphones wired 5 pin Cobra/Uniden and adapt to Cobra/President/uniden 4 pin. Also to Radio Shack 5 pin DIN, Tech808 do you have any sorce for these adapters. Thank you |
Tech808
Moderator
Username: Tech808
Post Number: 1628
Registered: 8-2002
| | Posted on Wednesday, February 25, 2004 - 7:24 am: |
|
Yankee,
Sorry but no. As the Cobra/Uniden 4 pin is the most popular most of the adapters go from 4 to 5 pin or 4 to 6 pin.
Now that Magnum has come out with the 4 Pin on the Magnum S-3 maybe they will consider useing the 4 pin on all of the New Magnum Radio's in the future.
Lon
Tech808 |
Spydrman
Junior Member
Username: Spydrman
Post Number: 41
Registered: 12-2001
| | Posted on Wednesday, February 25, 2004 - 9:22 am: |
|
Thanks for the replies |
