Copper Talk » Ask The Tech » Microphone Wiring » Turner SSB +2 to Uniden Washington « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Biskybabyusa
Member
Username: Biskybabyusa

Post Number: 52
Registered: 11-2006


Posted on Wednesday, July 18, 2007 - 11:26 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Any ideas on that config ! Thanks Jim

Moderator Note!

Which Model of Uniden Washington?

The Uniden Washington 4 pin with the 858PLL wire's differently than the Uniden Washington 5 pin with the 8719 PLL
Top of pagePrevious messageNext messageBottom of page Link to this message

Dale
Senior Member
Username: Dale

Post Number: 1006
Registered: 12-2002
Posted on Thursday, July 19, 2007 - 5:32 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

if its 6 wire try this
1]white
2]shield
3]black
4]red
5]blue
dale/a.k.a.hotrod
cef426
cvc#64
Top of pagePrevious messageNext messageBottom of page Link to this message

Biskybabyusa
Member
Username: Biskybabyusa

Post Number: 53
Registered: 11-2006


Posted on Thursday, July 19, 2007 - 9:22 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Dale, Thanks. I tried that. Wasn't right. There are 6 wires. The yellow wire is clipped short and probably not used. Had thing close though, would recieve when the mic was keyed. I ran out of patience last night. I was thinking of maybe wiring it for my RCI 2990 or galaxy 2527 to use on sideband. Any ideas on that wiring ? Interesting, it has a small black switch on the bottom that barely moves back and forth. Not sure what this is ( may have been added later) Thanks, Jim
Top of pagePrevious messageNext messageBottom of page Link to this message

Dale
Senior Member
Username: Dale

Post Number: 1009
Registered: 12-2002
Posted on Thursday, July 19, 2007 - 10:31 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

what happens does it key up?
no recieve?
keys up radio without actually keying mike?
tell us a little more info
the switch does it say electronic then relay on bottom?if so set to electronic.my plus 3 has this switch.im going to do a google search for
more info.ive only had the plus 3 and superside kick
dale/a.k.a.hotrod
cef426
cvc#64
Top of pagePrevious messageNext messageBottom of page Link to this message

Starface
Senior Member
Username: Starface

Post Number: 1393
Registered: 1-2005


Posted on Thursday, July 19, 2007 - 11:52 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Model: Washington
standard wiring:
Pin1=Audio
Pin2=Shield
Pin3=Receive
Pin4=Switching Wire
Pin5=Transmit


Turner wiring:
Pin1=White
Pin2=Shield
Pin3=Black
Pin4=Red
Pin5=Blue


This Information is also listed to the left under:

Tools
Mic. Wiring
STARFACE
CEF#476
KI4NBE
HAM#181
CVC#Ø14





Top of pagePrevious messageNext messageBottom of page Link to this message

Biskybabyusa
Member
Username: Biskybabyusa

Post Number: 56
Registered: 11-2006


Posted on Friday, July 20, 2007 - 8:01 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Dale, It is the Washington with the 8719 Pll. The radio would recieve when the mic was keyed. I will see this weekend which radio I willwire it for. I do use a jumper for most of my mices, so I can use them with different radios, 5 pin to 6 pin. That's why I wanted to wire it for the Washington. Thanks, Jim. Oh, I'll also check out that little switch on the bottom. It doesn'tseem to move very much, so don't know if it works correctly.
Top of pagePrevious messageNext messageBottom of page Link to this message

Dale
Senior Member
Username: Dale

Post Number: 1013
Registered: 12-2002
Posted on Friday, July 20, 2007 - 7:52 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

check that switch.im really unsure as why it
wouldnt work.i got 2 places i got my info
from 1 of them is left of this post under tools.
on my plus3 its exactly the same when in relay
position.but put it into electronic works fine
try that i couldnt find wiring skmatics for that
particlar mike
dale/a.k.a.hotrod
cef426
cvc#64
Top of pagePrevious messageNext messageBottom of page Link to this message

Biskybabyusa
Member
Username: Biskybabyusa

Post Number: 57
Registered: 11-2006


Posted on Monday, July 23, 2007 - 1:11 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Dale, Someone had put a small plate over the old switch so it wouldn't move back and forth. I removed it and now it will work back and forth for electronic switching or not. Thank you....
Top of pagePrevious messageNext messageBottom of page Link to this message

Biskybabyusa
Member
Username: Biskybabyusa

Post Number: 59
Registered: 11-2006


Posted on Monday, July 23, 2007 - 12:50 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Thanks, Dale. Will try the switch again !
Top of pagePrevious messageNext messageBottom of page Link to this message

Captian_radio
Intermediate Member
Username: Captian_radio

Post Number: 274
Registered: 9-2004
Posted on Wednesday, November 21, 2007 - 9:26 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

I have a Turner +2 desk mic and it only has 4 wires it is still at factory specs,did you say yours has 5 wires? I have never seen a Turner +2 with more than 4 wires.If the radio loses rx when you pull the mic out then it might not work.The old Turner +2's were designed mostly to work with relay switching and some of the older radios from back in the late 70's and early 80's
Bob CEF451/VE1CZ
Robert L. Spicer The days of radio are just beginning!

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: