| Author |
Message |
    
Sharpshooter007
Junior Member
Username: Sharpshooter007
Post Number: 21
Registered: 10-2009
| | Posted on Wednesday, October 09, 2013 - 11:20 am: | 
|
Hello again.. I was thinking about installing a sx-175 cab on my omegaforce S45hp. Seeing that it already has the rfx-75 pre installed from the factory does anyone know of any one who has done this? |
Dale
Senior Member
Username: Dale
Post Number: 1973
Registered: 12-2002
| | Posted on Saturday, October 12, 2013 - 12:37 pm: |
|
the sx-175 was designed for radios with a front
mic . your s45 has dual side mics, i highly doubt
it will work.however there another one called
a rfx 150 it fits on back of radio same as the rfx 75.
dale/a.k.a.hotrod
cef426
cvc#64
454 [dx numbers]
38lsb
|
Sharpshooter007
Junior Member
Username: Sharpshooter007
Post Number: 22
Registered: 10-2009
| | Posted on Tuesday, October 15, 2013 - 11:12 am: |
|
Very true.. would u happen to know if I would need to relocate the driver and final from the rfx 75 to the inside of the chassis? If I am not mistaken, and I could be, the rfx 150 is a stand alone unit. If I were to set it up correctly, I could use the rfx 75 as a driver for the rfx 150. As long as I dont feed it too much. |
Dale
Senior Member
Username: Dale
Post Number: 1976
Registered: 12-2002
| | Posted on Tuesday, October 15, 2013 - 6:45 pm: |
|
not really sure what you mean?? both units
have everything inside the box. both stand alone
the rfx 75 would be WAY too much drive. and not
recommended.
dale/a.k.a.hotrod
cef426
cvc#64
454 [dx numbers]
38lsb
|
Sharpshooter007
Junior Member
Username: Sharpshooter007
Post Number: 23
Registered: 10-2009
| | Posted on Thursday, October 17, 2013 - 9:29 am: |
|
I was assuming that the rfx 75 pre installed from the manufacturer was necessary for the function of the radio, that is why I thought the internals would need to be relocated. If they are both stand alone units, should be an easy swap. Now.. I do not have the proper equipment needed for an alignment, in your opinion, would you recomend getting it aligned after I install the rfx 150...? I would assume so, but ... |
Dale
Senior Member
Username: Dale
Post Number: 1978
Registered: 12-2002
| | Posted on Thursday, October 17, 2013 - 4:12 pm: |
|
personally if was me i think id have someone
you know who knows what thier doing do it.
i never done it but ive looked quickly thru the
instructions and YES you would have to at least
check the biasing level on the finals and adjust
am/ssb power.
dale/a.k.a.hotrod
cef426
cvc#64
454 [dx numbers]
38lsb
|
Sharpshooter007
Junior Member
Username: Sharpshooter007
Post Number: 24
Registered: 10-2009
| | Posted on Friday, October 18, 2013 - 11:42 am: |
|
fair enough.. i will try to keep the thread updated when i have made a decision on what to do. Thanks again for your time and input! |
Dale
Senior Member
Username: Dale
Post Number: 1980
Registered: 12-2002
| | Posted on Tuesday, October 22, 2013 - 6:56 pm: |
|
was hoping others would chime in here. im not a tech by any means.
dale/a.k.a.hotrod
cef426
cvc#64
454 [dx numbers]
38lsb
|
