| Author |
Message |
    
Biggdog259
| | Posted on Friday, September 05, 2003 - 10:48 pm: | 
|
can you tell me if the Kenwood mic will work on the 2970? And the wireing for it not real sure about it. |
Biggdog259
| | Posted on Saturday, September 06, 2003 - 9:24 am: |
|
My first time in a Forum,hope i am doing it ok?
Biggdog, You are doing Great and Welcome!
Lon
Tech808
|
Biggdog259
| | Posted on Saturday, September 06, 2003 - 5:18 pm: |
|
Lon if i get a response where do i go to get it? Biggdog
Biggdog,
It will be posted right here under your question.
Lon
Tech808
|
Biggdog259
| | Posted on Saturday, September 06, 2003 - 10:47 pm: |
|
Thanks Lon biggdog259 |
Biggdog259
| | Posted on Monday, September 08, 2003 - 8:55 pm: |
|
Lon would it be easier to put the MC50 mic. on a four pin radio like my Ranger RCI6900F? biggdog259 |
Scrapiron63
| | Posted on Monday, September 08, 2003 - 10:43 pm: |
|
Bigdog, how many wires does that mike have, and do you know how it wires to any radio. It should be fairly easy to wire it for the 2970. You just need to use the first three pins on the 6 pin plug.
1. shield
2. audio
3. tx
Pin 4 is receive, if the mike has a receive wire, but you don't have to have it wired for receive. Pins 5 and 6 are for changing channels. |
Biggdog259
| | Posted on Tuesday, September 09, 2003 - 12:29 am: |
|
scrapiron, the mic has 4 wires lost the wireing for the Kenwood it came with, so in the dark all around. biggdog |
Scrapiron63
| | Posted on Tuesday, September 09, 2003 - 10:12 am: |
|
Biggdog, i've never seen a MC-50, but this is how most mikes are: Look at the end of the cord, you may have to peel it back a little, the shield should be wrapped around one wire, that wire is the audio wire. If it's like this, you have two of the connections for the 2970, shield on pin 1, audio on pin 2. If you have an ohm meter, check the other two wires, one may show continuity with the shield, if so thats a ground also, and can be put on pin 1 with the shield. The other wire is TX, and should show continuity with shield with the mike keyed. This wire will go on pin 3. Thats all you need to make the 2970 work. If neither of the two wires show continuity with shield, find the one that does show continuity with shield with the mike keyed. That will be tx, and you can forget the 4th wire. Now, if one wire is not wrapped with the shield, we'll have to start over. Hope this makes sense. lol, scrapiron |
Biggdog259
| | Posted on Sunday, September 14, 2003 - 2:16 pm: |
|
Scrapiron would it be the same for the RCI 6900F to wire the MC50 to it. Biggdog |
Scrapiron63
| | Posted on Sunday, September 14, 2003 - 7:22 pm: |
|
Yep, its just a four pin, but will wire the same. |
Marc71
New member
Username: Marc71
Post Number: 7
Registered: 9-2018
| | Posted on Monday, January 18, 2021 - 11:56 pm: |
|
anybody know if a kenwood mc50 desk mic will work with a cobra 2000, and how to wire it. |
|
