Copper Talk » Ask The Tech » Modifications » Uniden PC68XL « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Dxmodulator
Junior Member
Username: Dxmodulator

Post Number: 11
Registered: 11-2004
Posted on Friday, February 11, 2005 - 8:51 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Are the uniden pc68xl and the cobra 25 the exact same radio? If so can I use the mods for the cobra 25 on the uniden pc68xl? I want to change the final to a 2SC1969 for more output. If the are diffrent radios then do you have a mod procuder to change the final in a uniden pc68xl?
Top of pagePrevious messageNext messageBottom of page Link to this message

Audiophile73
Junior Member
Username: Audiophile73

Post Number: 49
Registered: 5-2004
Posted on Saturday, February 12, 2005 - 3:44 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

just open up vr5 all the way for modulation, and peak it out. Get 16 watts or so and be done. If you want more power than that buy an amp. It doesn't have to be a big one. If you put a new final in it's a lot of work and a pain in the rear if you ask me. You can get a small amp for 30 or 40 bucks. Like the kl40, its 30 or 40 bucks and you get about 40 watts out of it. Just my opinion though
Top of pagePrevious messageNext messageBottom of page Link to this message

Weatherman49
New member
Username: Weatherman49

Post Number: 1
Registered: 2-2005
Posted on Sunday, February 20, 2005 - 11:27 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

the pc68xl and the pc66xl have the same boards so the mods for the 66 will work for the 68 as for the 25 I believe they are the same but not positive but ya can put the 1969 final in but if you don't put in a new driver i don't think you will get much more out of it i cant remember the #for the driver. I had a 29ltd that had the driver and final changed to these and put 25w out the back of the radio I was pleasently surprised and pleased good luck on your mods
Top of pagePrevious messageNext messageBottom of page Link to this message

Therealporkchop
Intermediate Member
Username: Therealporkchop

Post Number: 169
Registered: 11-2002


Posted on Tuesday, March 01, 2005 - 12:33 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

2SC1957 for that driver...driver
Top of pagePrevious messageNext messageBottom of page Link to this message

Mudducksoup
New member
Username: Mudducksoup

Post Number: 5
Registered: 6-2005
Posted on Monday, July 04, 2005 - 2:20 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

ive got a cobra 25 ltd and a uniden pc68 xl they look to have the same board and both have vr 25.so for the uniden im going to use vr 25.And could sombody tell me how to make a dummy load? All help is very apprerceated.well im outty and everybody have a safe and happy 4th.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sonoma
Intermediate Member
Username: Sonoma

Post Number: 196
Registered: 11-2001
Posted on Monday, July 04, 2005 - 3:06 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

not sure what you mean by using vr 25?
go to the left of this forum and click on modification list under tools and follow the rest and it will take you to the modifications for this radio.
Top of pagePrevious messageNext messageBottom of page Link to this message

Twowatt
New member
Username: Twowatt

Post Number: 2
Registered: 7-2005
Posted on Wednesday, July 06, 2005 - 5:10 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

hello mudducksoup. the easiest way i know is to get a 5w 51 ohm carbon resistor from r.f.parts, solder one lead into the pl-259 center pin (screw the outer shell back on), then solder the other lead to the pl-259 body. this is good enough for basic single final radios for short checks. (2 100ohm 2w resistors in parallel for 4w capability). for more power, another simple one is to get 20 1kohm 2w resistors (from some mail order company), 2 10" pieces of 1/4 inch or smaller copper tubing from your local hardware store, and solder each resistor to the tubing in a ladder like configuration, spacing them about 1/2" apart. solder the center conductor of some rg-8x to one pc of tubing and the shield to the other pc of tubing keeping the coax leads as short as reasonable but allowing for movement (of course a pl-259 on the other end of coax). now you have a good 40w dummy load to take on all of the tuning any dual 1969/2312 radio can dish out. i started using these (and others i made) in the 70's to tune up, check coax, adj swr on dual antennas etc, still have them and they work fine. hope this helps.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mudducksoup
Junior Member
Username: Mudducksoup

Post Number: 11
Registered: 6-2005
Posted on Wednesday, July 13, 2005 - 3:48 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

how do i put talkback in a uniden pc68xl i need the step by step. thanky for the help and im 10-6
Top of pagePrevious messageNext messageBottom of page Link to this message

Mudducksoup
Junior Member
Username: Mudducksoup

Post Number: 12
Registered: 6-2005
Posted on Thursday, July 14, 2005 - 3:06 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

thanky two watt im going to try to build the 40 watt dummy load i just have to git around to gitting it done. i appreciate the the help.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mudducksoup
Junior Member
Username: Mudducksoup

Post Number: 13
Registered: 6-2005
Posted on Thursday, July 14, 2005 - 3:12 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

i went to the mods section but dint find enuff info and im ready to git-er-done , so could enybody please explain to me how to put talkback in a uniden pc68xl. i would be very thankfull for eny info on this.oh btw great forum guys!
Top of pagePrevious messageNext messageBottom of page Link to this message

Tech808
Moderator
Username: Tech808

Post Number: 6344
Registered: 8-2002


Posted on Thursday, July 14, 2005 - 4:53 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Mudducksoup,

I brought the Topic Talk back back to the top of this area for you.

Hope this helps,

Lon
Tech808
CEF808
N9OSN
Top of pagePrevious messageNext messageBottom of page Link to this message

Vanillagorilla
Intermediate Member
Username: Vanillagorilla

Post Number: 151
Registered: 4-2005


Posted on Saturday, August 27, 2005 - 5:56 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)


Cheap and easy Talkback.
Open the bottom of your Cobra/Uniden radio.

Solder a small thin wire from the neg side of the speaker to DC ground...chassis should work fine. If it's too loud then put a 100ohm resistor inline or experiment with different values.Rat shack has them all for a few pennies.
If your handy put a variable pot outside the radio to control your talkback volume.
Too loud and she WILL squeal! May have to use your mic gain to lower it or use the stock mic.
As far as I know this only works on Cobra and Uniden radios.
You can do this OR buy an external "talkback" speaker with vol. control. :-)
Good Luck!

Hank '905
CEF 559
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 103
Registered: 3-2004
Posted on Monday, August 29, 2005 - 11:23 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Soder a 68pf to 100pf disc cap across C62 and you can get a better carrier.i personaly would go for an 8 watt carrier with forward swing if you can and you will add 1 s-unit to the radio recieveing you.And all the swing things are gimmicks what good is modulation with nothing to carry it? right.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 108
Registered: 3-2004
Posted on Thursday, September 01, 2005 - 10:47 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

last post is wrong not for cobra 25 its for the 29 sorry
Top of pagePrevious messageNext messageBottom of page Link to this message

Navyrebel782003
Junior Member
Username: Navyrebel782003

Post Number: 29
Registered: 12-2004


Posted on Tuesday, September 06, 2005 - 9:49 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

hey fusebreaker, correct me if I am wrong but I was told that vr4 is for your recieve, I have a 68 and want to try and get it back up and running, but cant remember exactly which one it is. thanks in advance for any help and info.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 119
Registered: 3-2004
Posted on Tuesday, September 06, 2005 - 11:37 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

im not sure give me a lil time ill look for a VR chart.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 120
Registered: 3-2004
Posted on Tuesday, September 06, 2005 - 11:49 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

i believe the 68 is the same as a cobra 25 if thats true then vr4 is the sqelch adjustment.Bare with me man and we will getcha going if i can im doing all i can
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 121
Registered: 3-2004
Posted on Tuesday, September 06, 2005 - 11:58 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

if its the same as a 25 cobra i see vr2 being your RX pot but keep in mind im no tech!!!
Lon or one of the techs will prolly know for sure
im not to fimalar with the 68 i only owned one cobra 25 in my 19 yrs so i could be wrong but you might try it let me know how it works.
Top of pagePrevious messageNext messageBottom of page Link to this message

Navyrebel782003
Junior Member
Username: Navyrebel782003

Post Number: 31
Registered: 12-2004


Posted on Wednesday, September 07, 2005 - 7:10 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

ok, well hey, that's somewhere to start anyway man, thanks again, I'll see what it gives me anyway, it will be my project radio anyway...lol
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 128
Registered: 3-2004
Posted on Wednesday, September 07, 2005 - 11:50 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

sounds fun

LOL
Top of pagePrevious messageNext messageBottom of page Link to this message

Navyrebel782003
Junior Member
Username: Navyrebel782003

Post Number: 32
Registered: 12-2004


Posted on Wednesday, September 07, 2005 - 2:58 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

oh yeah, it's loads of fun...lol. I got it working, now just need to get it aligned again and have the meter replaced, the plastice front is busted out of it, but it does still work...lol.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fusebreaker
Intermediate Member
Username: Fusebreaker

Post Number: 129
Registered: 3-2004
Posted on Wednesday, September 07, 2005 - 3:35 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

GREAT!! good to hear its working.My friend is giving me a Gold cobra 29 for free i cant wait im going to install the 1969/1957 finals and try to get the carrier up to 8.0 watts and get about 80% modulation he says it has a connex board and it might have the expo kit.So i take it VR2 was the right VR? I hope to hear you on the iar sometime.I am going to use the 29 in my truck and buy a ssb model for the house and throw up an A99 about 20 or 30 feet.I might invest in a 100 watt bacon frier to and run that on the base.
Why does the radio need re-aligned? is it off frequency?
I was at the local wal-mart (MONOPOLY) store and seen they have the pc68 for 79.96 seems a little high but maybe since its uniden its better than a cobra 25.
Are you going to do the final mod on your 68?
I personaly like having SSB on a radio but in the truck i just run channel 19 mostly.
Top of pagePrevious messageNext messageBottom of page Link to this message

Navyrebel782003
Junior Member
Username: Navyrebel782003

Post Number: 33
Registered: 12-2004


Posted on Thursday, September 08, 2005 - 5:21 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Actually, when I put it in my truck on the wilson 1000 mag mount and the dm 452 power mic it seems to work pretty good, but I think the recieve may still be a little off but it seems to be working. people say they can hear me good but they are very weak, I haven't tried to adjust vr2 yet but may try this weekend if I can and see what happens. I will let you know what I find out as soon as I can get too, but with 2 jobs it's hard to find time.

James
CEF 590

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: