Copper Talk » Ask The Tech » Ham Gear » Yaesu FT-2800M Modifications « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Therealporkchop
Intermediate Member
Username: Therealporkchop

Post Number: 183
Registered: 11-2002


Posted on Saturday, March 26, 2005 - 2:28 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Maybe this is in the right spot, if not I know it'll find it's way to the right place.

Anybody have any modifications for this radio. I've done the mic mod to it and that helped a lot. I've also done the mod to allow it to transmit on the freq's it receives on too. I'm looking for any other special mods (wink, wink).

Thanks...
Top of pagePrevious messageNext messageBottom of page Link to this message

Bc910
Intermediate Member
Username: Bc910

Post Number: 481
Registered: 7-2004


Posted on Saturday, March 26, 2005 - 8:39 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

BTW porkchop...
The mod you did to the radio for extra freqs is acheveable without even opening the covers and voiding the warrenty, just gotta push some buttons when powering on...
Sorry I don't know of any other mods, don't think there are none...
BC
Top of pagePrevious messageNext messageBottom of page Link to this message

Mrsandman
Member
Username: Mrsandman

Post Number: 63
Registered: 1-2002


Posted on Sunday, March 27, 2005 - 3:54 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

This MOD is for the NEW Yeasu FT-2800 Hi-Power 2-Meter Mobile and it is easy!

Start by disconnecting power and microphone.

Remove all screws on bottom of radio and remove bottom cover.

* Careful, the speakers rubber seal my stick to the cover, so take your time and note that the speakers wires are soldered to radio (no connector).


To make this simple, position the radio with the front facing away from you (bottom up) In the front right corner you will see a set of three solder pads located on the back side of the circuit board for the front display/ controls.


There is only one solder pad in place from factory (far right side, see photo).


REMOVE this solder pad!


Bridge the middle solder pad, leave the others un-soldered.


Reset radio by pressing ALL four white panel buttons while turning power on.
button labels ---> [MHz] [Rev] [LOW] [D/MR]

Then press the [D/MR] button. The radio will power cycle.
DONE!

NEW TX and RX RANGE is 137.000MHz to 174.000MHz

Enjoy!
2800
Top of pagePrevious messageNext messageBottom of page Link to this message

Therealporkchop
Intermediate Member
Username: Therealporkchop

Post Number: 193
Registered: 11-2002


Posted on Sunday, April 24, 2005 - 7:16 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Yeah that is the one I did already. I was just wondering if there were any others available. I did the mic mod also where you remove the little disc that sits in front of the mic element. It helped to clean up the audio and make it clearer and louder. I get good reports from it on the local repeater.

I've seen alot of radios/receivers that state that cell freq's are blocked. Are there mods for them to restore those?
Top of pagePrevious messageNext messageBottom of page Link to this message

Bruce
Senior Member
Username: Bruce

Post Number: 2530
Registered: 9-2003
Posted on Sunday, April 24, 2005 - 8:06 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Under federal law radios are not allowed to cover c-phones and if made after the mid 90's UNMODIFIABLE.
Top of pagePrevious messageNext messageBottom of page Link to this message

Therealporkchop
Intermediate Member
Username: Therealporkchop

Post Number: 196
Registered: 11-2002


Posted on Monday, April 25, 2005 - 3:41 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Now Bruce....Bruce....come'on now. For sure not. Of course you could get the Europe versions to solve that....

Anyone tried the FT-857 on 11 meters? How about you Bruce?
Top of pagePrevious messageNext messageBottom of page Link to this message

G0svh
New member
Username: G0svh

Post Number: 2
Registered: 7-2005
Posted on Sunday, September 25, 2005 - 4:07 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

whate the difference between the uk spec and the us spec, and anyone no the mod without opening the rig.

ed...........cef ham152

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: