Author |
Message |
Cdp1953
New member Username: Cdp1953
Post Number: 2 Registered: 7-2006
| Posted on Wednesday, January 10, 2007 - 4:02 pm: |
|
I need help wiring the 452 to the Magnum 257. The mic has a blue, yellow, black, red ,and shield wire. What goes to what pins? |
Tech808
Moderator Username: Tech808
Post Number: 12703 Registered: 8-2002
| Posted on Wednesday, January 10, 2007 - 5:45 pm: |
|
Cdp1953, SUPERSTAR DM-452 Microphone COBRA/UNIDEN Wiring: 4 ~ Pin Mic Plug Model Pin #1 Common / Yellow Pin #2 Audio Output / White Pin #3 Transmit / Red Pin #4 Receive / Black 5 Pin Mic Plug Model Pin #1 Audio Output / White Pin #2 Shield Pin #3 Receive / Black Pin #4 Common / Yellow Pin #5 Transmit / Red MAGNUM 257 Microphone Wiring: Pin #1 ~ Microphone Audio Pin #2 ~ Receive Pin #3 ~ Transmit Pin #4 ~ Down(Up w/22K Ohm Resistor) Pin #5 ~ Ground Pin #6 ~ +13.8VDC NOTE! Make sure Nothing comes into contact with this Pin on the radio. Your color of wires are different from the SUPERSTAR DM-452 so you must have a different brand but the pin out should be the same. Hope this help's Lon Tech808 N9CEF CEF#808/HAM#33 CVC#002
|
Cdp1953
New member Username: Cdp1953
Post Number: 3 Registered: 7-2006
| Posted on Wednesday, January 10, 2007 - 6:10 pm: |
|
I have the Aries DM-452. It is wired with 4 pin plug now. 1.Shield 2.yellow 3.blue 4.black Red is NC How do I convert this mic cable over to the 6 pin? Do I need the red, or swap it with another? |
Tech808
Moderator Username: Tech808
Post Number: 12704 Registered: 8-2002
| Posted on Wednesday, January 10, 2007 - 7:28 pm: |
|
Cdp1953, You will need a 6 pin Microphone Connector and you will only use PINS #1-2-3-5 on the 6 pin mic connector to connect to the Magnum 257. <font color="ff0000">CLICK HERE ®</font> MIC CONN 6PIN FEMALE PLUG You will need to figure out what wire went to each pin on the mic you have now and match to the pinout for the MAGNUM 257 listed in the above post. If you were using it on a Cobra/Uniden Radio you should have no problem's. The color of the wires may be different but the pinout should be the same. You will not use PIN #4 or #6 in the 6 Pin Mic connector. Lon Tech808 N9CEF CEF#808/HAM#33 CVC#002
|
Cdp1953
New member Username: Cdp1953
Post Number: 4 Registered: 7-2006
| Posted on Wednesday, January 10, 2007 - 7:37 pm: |
|
Your information was very helpful. I just wired it up and it is working great. Thank You! |
Tech808
Moderator Username: Tech808
Post Number: 12706 Registered: 8-2002
| Posted on Wednesday, January 10, 2007 - 7:42 pm: |
|
Cdp1953, Glad I could be of help and WELCOME to the COPPER FORUM. Lon Tech808 N9CEF CEF#808/HAM#33 CVC#002
|
Chad
Senior Member Username: Chad
Post Number: 1265 Registered: 11-2004
| Posted on Thursday, January 11, 2007 - 11:22 am: |
|
I'm not trying to spoil your soup but the stock mic is the best thing I have found for that radio, it's like they were "made for each other" Chad Chad CEF 433 HAM 212 not an ego thing, just keepin' the mods happy
|
Cdp1953
New member Username: Cdp1953
Post Number: 6 Registered: 7-2006
| Posted on Friday, January 12, 2007 - 8:41 pm: |
|
The stock mic was too small for my hand and I was always going off freq from bumping those up/dn buttons. I was also told that it was too bassy. The DM-452 cured that problem and now everyone says that I sound great! |
Hyperno_1979
Intermediate Member Username: Hyperno_1979
Post Number: 279 Registered: 12-2005
| Posted on Thursday, February 15, 2007 - 6:25 am: |
|
Wire your mic to Cobra 4 pin and buy the adapter from copper. That way you can just swap the mic from radio to radio without re-wiring. CEFFFCEF Bob CEF703 CVC26.
|