Copper Talk » Modifications » Radios » Galaxy saturn turbo swing « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Scorpion
Junior Member
Username: Scorpion

Post Number: 12
Registered: 4-2004
Posted on Wednesday, July 27, 2005 - 12:33 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

i have a saturn turbo & has very little swing i adjusted the hi&lo power to see if i can get it any better but not .i have a frinds turbo to see if it had any mods done nothing looks clipped or diffrent maybe i dont no what to look for but his radio has a real nice swing to it .where mine is limited.any ideas???????????????
Top of pagePrevious messageNext messageBottom of page Link to this message

Patzerozero
Senior Member
Username: Patzerozero

Post Number: 1099
Registered: 7-2004


Posted on Wednesday, July 27, 2005 - 11:00 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

where are you checking the swing-on the radios' meter, or an external wattmeter? if radios' meter, it could be adjusted DOWN so needle doesn't bounce off side of meter all the time. if external, did you see BOTH radios on SAME meter? 1 could be rms/avg & other could be PEP. what is dead key of yours & what is swing-read on an external meter( & what meter)?
lastly-is your radio 'getting out'? & what kind of signal reports does it get?
Top of pagePrevious messageNext messageBottom of page Link to this message

Inspector
Intermediate Member
Username: Inspector

Post Number: 147
Registered: 12-2001
Posted on Sunday, August 07, 2005 - 3:12 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

I have a Turbo, and I am sure you're familliar with the power supply problems in them...also remember that the main board drives the 100W amp in the back, so it can be real easy to mis-adjust and overdrive the amp. By bypassing the amp's keying circuit and relay, you can see exactly what the drive wattage is. Since the board is a one-final RCI-2950 board, you can try the heavy-swing modification (when applied propperly this can keep the amp cooler and prevent premature failure). Some Turbos came off the line, with the bias current set too high on the Amp's pills. This could cause problems like you describe (low modulation/ foreward drive).
Top of pagePrevious messageNext messageBottom of page Link to this message

Freebird
Intermediate Member
Username: Freebird

Post Number: 271
Registered: 1-2003


Posted on Wednesday, October 19, 2005 - 2:56 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

I have a turbo also and on side band mine sounds like the speaker is blow out but on AM it sounds fine.when i talk to people the tell me when i talk i get kinda distorted i wonder what that's all about?grrrr
Top of pagePrevious messageNext messageBottom of page Link to this message

Inspector
Intermediate Member
Username: Inspector

Post Number: 149
Registered: 12-2001
Posted on Friday, October 21, 2005 - 9:50 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

If the radio was ever "tuned-up", I would place my bets on the crappy power supply not giving you 1) enough current; or 2) a stable voltage...
Top of pagePrevious messageNext messageBottom of page Link to this message

Heavyweight
Member
Username: Heavyweight

Post Number: 51
Registered: 11-2004


Posted on Sunday, December 04, 2005 - 1:24 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

I have a turbo also and on side band mine sounds like the speaker is blow out but on AM it sounds fine.when i talk to people the tell me when i talk i get kinda distorted i wonder what that's all about?grrrr
Thats what happens when you clip this and turn this all the way to the right.Had the same problem with my 95T.I think it was Q39 that had been removed.Lots of mod on am but it sounded like Dirt on side band.Put Q39 back and it works great!

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: