Copper Talk » Ask The Tech » Amplifiers » TEXAS STAR 500 « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnny_be_good
Junior Member
Username: Johnny_be_good

Post Number: 26
Registered: 3-2005
Posted on Sunday, February 17, 2008 - 8:27 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Can anyone tell me if a Texas Star 500 and a Polamar 250 are different inside for 10 meter and 11 meter ssb or do they have to be changed and tuned by a tech to use on either band? Thanks John
Top of pagePrevious messageNext messageBottom of page Link to this message

Patzerozero
Senior Member
Username: Patzerozero

Post Number: 4153
Registered: 7-2004


Posted on Sunday, February 17, 2008 - 9:31 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

the dx500 will work fine on 28.500...as high as i've ever tried . never tried a palomar 250, but it'll probably be the same. most 'CB' transistor amps will work fine 26-30 mhz, give or take, with wattage USUALLY dropping at the ENDS. some may even go all the way down to 80m, transistor amps used to be made fairly cheaply & were pretty broad banded. not sure how effective CB amps are that are that broad.
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnny_be_good
Junior Member
Username: Johnny_be_good

Post Number: 27
Registered: 3-2005
Posted on Tuesday, February 19, 2008 - 8:23 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Thanks Patzerozero I ended up getting the three amps I asked about TS 500, TS 350, Polamar 225. Do you know where I can go to find info or user manual on using them? All I know is to keep the DK down on the TS,s but do I keep it on rec. while just listening and switch to amp while trans. and receiving or do I have to keep switching back and forth when talking and receiving? Also the small bulb behind the meter does not light up on either amp when powered up does it only light up while trans. or is the bulb burnt it looks ok by eye? How do I change the bulb inside the buttons each amp has one out? Are the bulbs 12v ? Sorry about all the questions but I am new to amps and I want to put together a strong emergency radio I wont be able to use them daily because neighbors are to close. I really enjoy this forum its a big help for newbies. Thanks again Patzerozero for the info. John
Top of pagePrevious messageNext messageBottom of page Link to this message

Tech808
Moderator
Username: Tech808

Post Number: 15309
Registered: 8-2002


Posted on Tuesday, February 19, 2008 - 9:18 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Johnny_be_good,

You can find information on all of the Texas Star amplifiers at:

www .texasstar.com


You can find information on the Palomar 225 by doing a Google Search at: www .google.com for: Palomar 225



Lon~Tech808
CEF#0808/HAM#001/CVC#0002

Tech808@copperelectronics.com
Top of pagePrevious messageNext messageBottom of page Link to this message

Patzerozero
Senior Member
Username: Patzerozero

Post Number: 4154
Registered: 7-2004


Posted on Thursday, February 21, 2008 - 9:06 am:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

sent you some info, j-b-g.
just leave it in line, press 1 of the power switches for it to be on, or leave it off, as long as dead key of radio is correct, doesn't matter, on or off. the relay inside the amp knows when you key up & sends signal through it,and lets receiver come back when you unkey.
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnny_be_good
Junior Member
Username: Johnny_be_good

Post Number: 30
Registered: 3-2005
Posted on Friday, February 22, 2008 - 12:20 pm:   Edit Post Delete Post    Move Post (Moderator/Admin Only)

Thanks again Patzerozero don't know what you ment by sent info but read your posting you sent did you ever remove the button caps to change the light bulb? John

Add Your Message Here
Post:
Username: Posting Information:
This is a private posting area. Only registered users and moderators may post messages here.
Password:
Options: Enable HTML code in message
Automatically activate URLs in message
Action: